Struck by rolling object or equipment-other than powered vehicle, n.e.c. · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Anthony Forest Products Company, 1236 URBANA RD., EL DORADO, ARKANSAS 71730
on — Fractures, affecting the lower leg(s).
Final narrative
An employee had finished unjamming logs in the log deck when he asked a coworker to use a log turner on the logs. The area was not completely cleared when the coworker used the log turner. One of the logs escaped and rolled onto the employee, injuring his left knee, fracturing his left fibula, and lacerating his right elbow.
HospitalizedLower leg(s)Logs
More severe injuries at Anthony Forest Products Company
During general clean-up activities, the edger machine malfunctioned and cut boards began ejecting from it. An employee was struck in the back by one of the boards and sustained five broken ribs.
An employee was pushing carts into the chute area for customers to retrieve. The first of six carts struck the wall and caused the other carts to bounce back and strike the employee. The carts knocked the employee to the ground and she sustained a back injury.
An employee was loading a portable storage container onto a dovetail trailer. This requires hooking up a bridle to the container and lifting the container enough for the dovetail to begin to slide under it. The employee reached and held the bridle lock to allow the trailer to move under it when the trailer moved backward instead of forward and caught his finger. The employee's right middle finger was amputated between the fingernail and the first knuckle.
An employee was reaching over a small stack of steel billets on the ground to cut a strap. When the strap was cut, one of the billets (weighing 5,182 pounds) rolled down onto his right leg. He was pinned and suffered a broken tibia. The incident occurred while the employee was training.
On June 7, 2023, employees were unloading a box truck and rolling a reel of 2-inch plastic pipe to the back of the truck. As the employees were rolling the reel, the edge of the steel frame of the reel contacted the side of the truck. The injured employee s right little finger was caught between the reel and the truck, resulting in a laceration and fracture as well as a little finger amputation.
Employees were using a dolly to remove a trash compactor unit from a residential home. As they began to transport it out of the room and to the outside, the dolly encountered uneven ground. This caused the dolly and the unit to move quicker than expected. The injured employee's left hand was then caught between a nearby concrete column and the compactor unit, resulting in fractures of the left ring and middle fingers that required amputation.
More severe injuries in this industry (NAICS 321113)
An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.
An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.
An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.
While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.