Struck by swinging or slipping object, other than handheld, n.e.c. · Fractures and other injuries, n.e.c.
At a glance
Federal OSHA recorded a severe workplace injury
at GRT Rubber Technologies, 201 Dana Dr, PARAGOULD, ARKANSAS 72450
on — Fractures and other injuries, n.e.c., affecting the multiple body parts, n.e.c..
Final narrative
An employee was struck by a lower roller from a feeding machine. The employee was feeding cloth and rubber from the back of the machine. Tension built up and caused the roll to swing out from the machine. The employee sustained multiple injuries, which led to hospitalization: internal injuries, possible right arm fracture, three broken right-side ribs, and 6-inch laceration to right abdomen.
HospitalizedMultiple body parts, n.e.c.Metal, woodworking, and special material machinery, unspecified
An employee was removing rubber product from a calender roll's rollers. The rollers caught the employee's arm, burning the forearm and elbow with their heat.
An employee was operating a rubber calendar mill when his left hand contacted a moving fabric sheet and was then pulled under a roller. His left arm broke in two places as he was removing it from the equipment.
A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.
An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.
The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.
An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.
An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.
More severe injuries in this industry (NAICS 326220)
An employee was preparing to cut rubber stock on a pneumatic cutting machine when their middle and ring fingertips were amputated by the cutting blade.
At about 12:25 a.m. on September 3, 2025, an employee was troubleshooting a malfunction involving a slitter whose arbor was not rotating as expected. The employee was observing the slitter's operations when the arbor completed its cycle and the employee's right index finger was drawn into the slitter's 4-inch, non-rotating cutting blade. The fingertip was amputated.
An employee was operating a rolling rope machine. Tooling fell out of the machine and landed on the employee's foot, breaking bones. The machine was not guarded at the time.
An employee was operating a machine when hot air and water was released. The employee sustained burns to the neck, back, buttocks and leg on the right side.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.