Vining and Son

An employee was collecting trash when they were struck by a rolling utility trailer. The employee sustained a right ankle fracture.

An employee was unrigging steel when an 8-inch by 50-foot, 4,875-pound piece of steel rolled onto their left leg, resulting in a fracture.

An employee was connecting a dolly to a trailer. The equipment rolled away, causing the employee's left index finger to be crushed between the trailer and the dolly. The employee sustained amputation of the fingertip.

On October 17, 2023, at 9:55 p.m., an employee was working on a ramp while moving merchandise from a cargo loader to a dolly. The employee was putting the locks on the dolly and transferring a unit load device containing packages when she realized the lock was in the down position. As she attempted to fix the lock, the unit load device started moving toward the dolly, and the employee became wedged between the dolly and the device. The employee suffered an injury to her lower left leg.

Two employees were shaking out steel beams and standing them vertically. One beam was hit, causing the other beams to fall. A beam then rolled over an employee's left shin and fractured it. The employee was hospitalized and required surgery.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee fell while stepping off the tailgate of a pickup truck. The employee landed on the ground and suffered a broken left fibula and tibia.

On October 7, 2025, employees were conducting trenching operations for the installation of a new sewer line system. The excavator's bucket was detached and put inside the trench as it was being exchanged for a different-sized bucket. An employee entered the trench with a shovel to move some dirt located at the front end of the pipe. The excavator bucket shifted and slid, striking the employee s right foot and trapping it against the ground. The employee sustained a fractured right tibia.

Employees were working to dislodge a large truck that was stuck in a rut using tow straps and a front-end loader with the bucket removed. An employee connected the straps to the loader and truck and another employee slowly engaged the loader to close the coupler. The injured employee's arm became caught in a pinch point. The employee was hospitalized with a fractured arm.

An employee was lifting a piece of 30-inch line stopping equipment using a jack screw. A lifting eye weld snapped and the load dropped. The end of the jack screw then landed on the employee's heel and crushed it. The employee was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.