B & H Construction

An employee was hospitalized after being struck in the head by a falling pipe.

An employee was checking an HVAC unit in the attic when they fell approximately 15 feet through the rafters to the floor. The employee sustained fractures to the ribs and scapula as well as a collapsed lung.

An employee was removing grating to change metal chip hoppers located in a pit. The employee lost his balance and fell approximately 12 feet from the grate, landing in the metal chip hopper. The employee sustained a sprained right foot, a left foot fracture, and a fractured L5 vertebra.

An employee was reviewing the next steps to take with the foreman when some material fell from above and landed near them. The injured employee then looked up, took a step on the catwalk, and fell through a gap, landing on the ground 15 feet below. The employee sustained three fractured vertebrae and a head laceration.

0n November 16, 2023, an employee was climbing onto a catwalk to cut valves for unit heaters in a building. The employee fell 14 feet through the attic onto the concrete floor, resulting in a fractured pelvis.

An employee was removing a rooftop curb when they fell approximately 15 feet through an opening in the roof, resulting in a fractured leg that required hospitalization.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.