Shureline Construction Inc.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

A flagger was directing traffic flow in a highway work zone. They were standing approximately 1.5 feet behind the shoulder's demarcating line, next to and slightly behind a traffic drum. As they were directing traffic into and out of the driveway of a parking lot, a car attempted to get around a truck and struck the traffic drum, which subsequently struck the employee, who was thrown 15 feet and landed on top of concrete aggregate. The employee suffered pelvic and rib fractures, T10 and L3 vertebra fractures, and internal bleeding.

An employee was troubleshooting a power washer in the field. Because there might have been water in its fuel, he brought it back to the shop and drained about a gallon of fuel from the tank into a plastic container. Some of the fuel spilled onto the floor and ignited. The employee was stomping out the fire when he lost his balance and tripped into a stool, which caused the plastic container to spill more fuel onto the fire. The employee's pants and shirt caught on fire, and he fell, abrading his knee while trying to get through the flames. As well as the knee abrasion, he suffered burns to the left leg and left lower quadrant of the torso. He was hospitalized.

An employee was backing up a tram (towing powered industrial equipment) to connect it to a trash bin. The employee's left forearm/wrist was caught and crushed between the tram and the bin. The employee was hospitalized.

An employee went to lift a carton and tripped on a different carton that was on the floor. She fell on the floor in the backroom and sustained a fractured right hip, and abrasions to her arm and knee. The employee was hospitalized and required surgery.

An employee was conducting a delivery of beverage products and began having cramps due to dehydration. The employee was hospitalized.