BIEWER-WISCONSIN SAWMILL, INC.

A maintenance employee was dismantling a kiln. As he was pulling top panels apart, a panel gave out and he fell approximately 6-8 feet, resulting in a fractured lower vertebra and a bruised lung. Fall protection was not tied off at the time.

On May 6, 2021, an employee was unjamming a machine. As a sorter bin was lowering, the employee's left index finger was pulled into the pulley system resulting in a fingertip amputation.

On September 13, 2018, at approximately 11:00 p.m., an employee operating a CNS computer identified a blocked photo eye and used water to clean the photo eye. The employee then saw wood in the machine and was attempting to remove it when the employee contacted the spline remover, resulting in an amputation of the right hand.

An employee was trying to remove a board that was lodged in the infeed of an edger when his right ring finger made contact with the cutter-head and was amputated.

A PSI blower chip loading system plugged up and tripped the breaker. A maintenance employee locked out the machine, cleared the plug, and restarted the machine. The employee was checking for air flow through the pipes with his right index finger hanging at the stop plate when the mechanical sleeve lacerated the finger pad. The machine amputated a chunk of the right index finger pad. The fingernail and part of the bone were removed to close the skin around the end of the finger.

An employee was changing a saw blade when the saw machine activated. The employee's left ring and little fingers were amputated.

An employee was clearing a jam from the label cutting machine when their left middle finger was partially amputated.

Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.

An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.

An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.

An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.

An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.

An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.

An employee was working to get a log back onto a carriage. The employee came into contact with the running saw, which amputated their arm.

While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.