BATTLE LUMBER CO., INC.

An employee was cutting a board with a chop saw when the blade partially amputated the employee's finger.

Two employees were operating forklifts throughout the facility. The first employee was leading and the second was following at the time of the incident. Both employees were operating without loads. While traveling, the first employee made an abrupt turn in front of the second employee. The second employee was unable to stop or swerve to avoid collision and ran into the rear of the first employee's forklift, causing it to roll over. The first employee's foot was pinned and broken between the forklift and the ground.

An employee was adjusting the lumber on a chain conveyor when the chain came off the sprocket. His left hand was caught by the chain and sprocket pulley as he tried to put the chain back on the sprocket, partially amputating his pinky finger (first knuckle), fracturing his ring finger, and damaging the ligaments on his other fingers. The chain conveyor was moving at the time of the incident.

An employee was caught between a stack of lumber and a chain guard, injuring the internal left pelvic area. The employee was hospitalized and had surgery.

An employee's right hand was caught in a chain/sprocket system between the grain change and unscrambler machines, injuring four fingers.

An employee was walking to their truck to look for a lid. When they stepped between the truck and a dock plate, they sustained a knee injury that required surgery.

An employee was standing on plant bed timbers, using a powered hand trimmer to trim the shrubs in the plant bed. The timber gave way, breaking into several pieces. The employee lost balance and fell with the trimmer in his hand. He suffered a severe laceration to the right wrist and hand.

A mail carrier slipped on ice and sustained a strain that required hospitalization.

An employee was loading phosphoric acid onto a rail car and preparing to secure the rail car for transport. While repositioning the loadout spout to secure it back to the drip pan holster on the dock, the spout contacted the handrail of the rail car, causing the employee to lose balance. The employee stepped back and their right foot entered the opening for the rail car, causing him to twist/pivot on his left leg. The employee's lower left leg was fractured.

On November 14, 2023, an employee was receiving a delivery from a truck when some of the merchandise fell from the truck s lift and struck him. He then fell to the ground and his head struck the sidewalk, resulting in an injury that required hospitalization.

An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.

An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.

An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.