GERRITY INDUSTRIES

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was stepping out of a car when they slipped and fell on ice, resulting in a femur fracture.

An employee was closing up for the weekend when they slipped on oil and brake fluid and fell. The employee suffered a leg fracture.

An employee was working in the forest flagging an area to be harvested. He took a step and his foot slipped on a stick hidden under the leaves, causing him to fall to the ground. He landed on his right foot/lower leg resulting in a fractured tibia.

An employee was inspecting an apartment to ensure it was ready for a new resident to move in. The carpet in the apartment had been recently cleaned and was still wet. As the employee went from the carpet to the tiled floor of the bathroom, they slipped and fell, resulting in a torn left hamstring.

An employee was delivering a letter along a rural carrier route when she stepped on an ice-covered snow drift, slipped, and fell to the ground. The employee sustained a right hip fracture that required surgery.

An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.

An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.

An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.