105,313Records 71,083Employers 85,290Hospitalizations 27,770Amputations 2015-01-01 2025-10-31
Safety Incidents OSHA Severe Injury Reports · 2015–2025

Norris Rods, Inc

Struck against moving part of machinery or equipment · Cuts, lacerations

Federal OSHA recorded a severe workplace injury at Norris Rods, Inc, 4801 W 49th St, TULSA, OKLAHOMA 74107 on — Cuts, lacerations, affecting the finger(s), fingernail(s), unspecified.

Watch Norris Rods, Inc — free Get an email when a new federal OSHA severe-injury report for Norris Rods, Inc is published. One employer, no account, unsubscribe in one click.

An employee was setting up a centerless grinder when his hand contacted the grinding wheel. The employee was hospitalized for laceration to the right middle and ring finger.

Hospitalized Finger(s), fingernail(s), unspecified Grinders, abraders

Leidy's LLC

An employee was operating a band saw when his right little fingertip was amputated.

Swift Beef Company

An employee was operating a strip saw. As the employee shut off the saw, their right index and middle fingertips were amputated by the blade before it came to a complete stop.

Kitchen Tune-Up

An employee was using a table saw to cut a piece of wood for wall framing. The wood jumped, causing the employee's hand to move toward the saw, amputating their left index finger and causing a laceration on their hand.

BBCJ LUMBER LLC

An employee was operating a trim saw. While trying to free a jammed board she had just cut, she came into contact with the running saw blade, which amputated her right thumb.

Appalachian Wood Floors, Inc.

An employee was using a shaper to cut wood when their right hand contacted the blade, resulting in a partial amputation to the right ring finger.

Renegade Group LLC

Employees were replacing a 24" pig trap door. A strap was shackled on the pig trap door and connected to a forklift. Welders began to cut the door off. An employee was holding onto the door when the cut was finished. The door shifted and caught his fingers, resulting in a hand injury and amputation.

Guidant Measurement

An employee was fitting an arbor fixture into a rotor housing to be reworked. The rotor is moved by a hoist. The arbor was being lowered into the rotor housing when the arbor slipped down onto his hand and amputated a portion of his left thumb.

Aztecwell

A crew was tripping out of the hole with an electrical submersible pump (ESP) in the process of swapping tubing tong heads to break down the ESP. An employee's left arm was caught and pinched by the tubing tongs. The employee sustained three lacerations and a fracture to the arm.

Hunting Energy Services

On May 21, 2025, at approximately 3:40 PM, a machinist was preparing a CNC lathe machine for it's next run. He was closing the machine door to complete the tooling setup when the door crushed his right middle finger. The employee required a surgical amputation to his fingertip.

Rae Corporation

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

Meeco Sullivan

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

Edward Jones Investments

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

Burgess Manufacturing of Oklahoma Inc.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.