Indirect exposure to electricity, unspecified · Second degree electrical burns
At a glance
Federal OSHA recorded a severe workplace injury
at D-T Steel Inc, 3866 Wrightsboro Rd., AUGUSTA, GEORGIA 30909
on — Second degree electrical burns, affecting the multiple body parts, n.e.c..
Final narrative
An employee was welding clips onto the end of the bridging of a wall, then installing bolts through the clips to the wall. As the employee lowered his rod holder down into the lift basket, the rod contacted the basket and energized it. As the employee leaned forward, they contacted the basket and grounded joist, resulting in first- and second-degree electrical burns to the stomach, back, and arms.
HospitalizedMultiple body parts, n.e.c.Aerial lifts, scissor lifts-except truck-mounted
An employee was on the ground preparing to receive a wire stringing steel rope being flown by a helicopter. The employee grabbed the steel line and was shocked by electricity from the line on his right hand. The employee was hospitalized and required surgery for nerve damage to his hand.
An employee was pulling a line through a light pole when it contacted an uninsulated line. The employee was shocked and sustained burns that required hospitalization.
An employee was in a bucket truck drilling a hole into a utility pole when a conductor located above the employee broke free from the pole and fell onto the equipment. The employee suffered second-degree burns to the right side of their face.
An employee was setting up to install a street light. As the employee placed the light pole on the ground, it became energized, causing the employee to sustain electrical burns to the left foot and hand, right hand, and right big toe.
More severe injuries in this industry (NAICS 238120)
An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.
An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.
An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.
An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.
An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.
An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.
During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.
An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.