Louisiana Pacific Corporation

An employee was holding the door for a co-worker when the tip of his right thumb was pinched and severed between the jamb and the door edge. The employee sustained an amputation of the distal thumb tip.

On January 20, 2025, an employee was walking between buildings when they slipped on ice and fell. The employee was hospitalized with fractures to their left tibia and fibula.

The injured employee was on the ground level receiving an OSB board from a co-worker who was on a 10-foot-high catwalk. The board was 4 feet by 25 feet and weighed approximately 270 pounds. As it was being slid down a handrail by a crew of three employees, the board went over the rail and landed on the injured employee's left foot, resulting in a fracture.

An employee was troubleshooting an airlock screw. The airlock's rotating blade struck the employee's right index, middle, and ring fingertips, resulting in partial amputations.

An employee exited their car and walked a few feet across a gravel parking lot when they fell to the ground, resulting in a fractured hip and abrasions to their face.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

A temporary employee turned off a planer machine, opened the housing, and began clearing a jam. The machine's spinning blade caught his right hand and degloved the index finger.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was working to dislodge a piece of stray veneer from a conveyor. The employee set up a ladder against the machine and climbed the ladder. He placed his left hand on the rail of the conveyor and his fingers were caught in the chain and sprocket assembly that powers the conveyor. Three fingers were amputated. The machine was guarded at the time.

A maintenance employee was changing a shaft on a piece of equipment that had been isolated for repair. While positioning the shaft into place, the shaft fell approximately two feet and pinched the employee's left index finger. The employee suffered a partial amputation of the fingertip without bone loss.

An employee was using a cart to move saw blades. The cart tipped over, striking and pinning the employee under the blades. The employee sustained severe lacerations to their torso and legs that required surgery.

An employee was labeling and writing on the back of a slab of quartz. The material was leaned toward him when the A-frame it was resting on shifted, causing the material to fall onto his right leg and break it.

An employee performed maintenance on various machines when they began to feel hot and unwell, and they experienced cramping. The employee was hospitalized with heat stress or dehydration.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.