PalletOne of Maine, Inc.

An employee was troubleshooting an issue with a notcher when his right middle and index fingers contacted the blades. The employee suffered an amputation of the middle finger.

An employee was strapping pallets on a flatbed truck when they fell from the truck to the ground, resulting in a broken hip that required hospitalization.

An employee's right ring finger was caught by the block and piston on a nailing machine when the drive fired. The fingertip was crushed and amputated.

An employee was loading the chamfer machine with wood and crushed their left index finger between a board and the machine guard. The fingertip was surgically amputated.

An employee was operating a chop saw when his middle finger was amputated up to the first knuckle and his index fingertip was also amputated.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

A temporary employee turned off a planer machine, opened the housing, and began clearing a jam. The machine's spinning blade caught his right hand and degloved the index finger.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.

An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.

An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.