Arkansas Electric Cooperatives, Inc

An employee was setting an electrical pole into the ground. As the pole was being raised, the choker on the pole slipped, catching the employee's third left finger in a pinch point. The distal portion of his finger was amputated.

The employee was tightening a belt on the wood chipper. After the repair, the employee turned the machine off. While the machine was coasting to a stop the employee got his left hand caught between the belt and pulley of the wood chipper, resulting in the amputation of two fingers.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was cleaning leaves with a backpack blower when he fell from a ladder, resulting in injuries to his head, neck, and back.

An employee was helping to set up a mulch blowing truck when they were struck by an oncoming vehicle. The employee was hospitalized with a fractured knee, a concussion, and a head laceration; they also received stitches on their arm.

An employee was rappelling down a tree. When he was most of the way down, he fell on the ground and suffered a broken pelvis.

An employee was using a table saw to cut a piece of wood when the saw cut his thumb, index, and middle fingers. His index finger was amputated and he was hospitalized.

An employee was mowing a residential lawn at a client's house. The mower slid on the land and tipped over onto him. The employee was hospitalized with a fractured vertebra in the neck and partial paralysis.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.