Struck by running powered equipment during maintenance, cleaning, testing · Cuts, lacerations, punctures without injury to internal structures
At a glance
Federal OSHA recorded a severe workplace injury
at Specialty Manufacturing of Menomonie, LLC, 205 East Street, BOYCEVILLE, WISCONSIN 54725
on — Cuts, lacerations, punctures without injury to internal structures, affecting the Other finger(s) n.e.c..
Final narrative
On May 7, 2025, an employee was unplugging a blocked sawdust discharge on a gang saw he had been using. His right hand came into contact with the spinning saw blade, and he suffered severe injuries to the ring and little fingers. He was hospitalized for surgery.
Hospitalized Other finger(s) n.e.c. Stationary sawing machinery stationary n.e.c.
More severe injuries at Specialty Manufacturing of Menomonie, LLC
On February 7, 2020, an employee was operating an up-cut saw to cut 2 x 12's when he made contact with the spinning circular blade, resulting in a partial amputation to the right index finger.
A temporary employee turned off a planer machine, opened the housing, and began clearing a jam. The machine's spinning blade caught his right hand and degloved the index finger.
An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
More severe injuries in this industry (NAICS 321920)
An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.
Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.
An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.
An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.
The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.
An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.