BERGHOLZ, OH —
OSHA Inspection: BILL DENOON LUMBER COMPANY DBA CLAYCO DRY KILN
Referral inspection · Health discipline
At a glance
On , OSHA opened a referral health inspection of BILL DENOON LUMBER COMPANY DBA CLAYCO DRY KILN in 5860 STATE ROUTE 164, BERGHOLZ, OH 43908 (NAICS 321918). OSHA activity number 313156044.
Where did this inspection happen?
- Establishment
- BILL DENOON LUMBER COMPANY DBA CLAYCO DRY KILN
- Site address
- 5860 STATE ROUTE 164
- City
- BERGHOLZ
- State
- OH
- ZIP
- 43908
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321918
- SIC code (legacy)
- 2431
- Employees
- 42
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- May 24, 2010
- Abate by
- Dec 24, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
E101E200
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to wood dust explosion, deflagration, or other fire hazards: a.On or about April 14, 2010, in the old moulder building, the dust collected by the Rees C/CX enclosureless dust collector was not removed at least daily when in use. ABATEMENT NOTE: Among other methods, one feasible and acceptable method to correct these hazards include following NFPA 664, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities (2007 Edition), Section 8.2.2.5.1.4, including, but not limited to, removing the collected dust at least daily or more frequently if necessary to ensure efficient operation. b.On or about April 14, 2010, in the old moulder building, the dust collected by the Coral Antipollution System enclosureless dust collector was not removed at least daily when in use. ABATEMENT NOTE: Among other methods, one feasible and acceptable method to correct these hazards include following NFPA 664, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities (2007 Edition), Section 8.2.2.5.1.4, including, but not limited to, removing the collected dust at least daily or more frequently if necessary to ensure efficient operation. c.On or about April 14, 2010, in the moulder building where exhaust air was recycled, the Air and Noise Products dust collection system was not equipped with listed spark detection, and the exhaust air ducts conveying the recycled air back into the building were not equipped with a high-speed abort gate activated by the spark detector, an explosion diverter, or equivalent. ABATEMENT NOTE: Among other methods, one feasible and acceptable method to correct these hazards include following NFPA 664, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities (2007 Edition), Section 8.2.2.6.2, including, but not limited to, installing a listed spark detection system located on the duct upstream from the dust collector and downstream from the last material entry point, or on the exhaust side of the dust collector, to detect fire entering or occurring within the dust collector, respectively, and installing a high-speed abort gate with a manual reset activated by the spark detector to intercept and divert any burning material to atmosphere before it can enter the plant. d.On or about April 14, 2010, in the saw building where exhaust air was recycled, the exhaust air duct conveying the recycled air from the Farr dust collection system back into the building was not equipped with a high-speed abort gate activated by the spark detector, an explosion diverter, or equivalent. ABATEMENT NOTE: Among other methods, one feasible and acceptable method to correct these hazards include following NFPA 664, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities (2007 Edition), Section 8.2.2.6.2, including, but not limited to, installing a high-speed abort gate with a manual reset activated by the spark detector to intercept and divert any burning material to atmosphere before it can enter the plant. e.On or about April 14, 2010, near the wood grinding room, the Industrial Air Technologies scrap silo was not equipped with either deflagration relief venting or an explosion suppression system. ABATEMENT NOTE: Among other methods, one feasible and acceptable method to correct these hazards include following NFPA 664, Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities (2007 Edition), Section 8.10.3.2, including, but not limited to, installing either deflagration relief venting designed to relieve the deflagration to a safe area andmaintain the pressure below the yield strength of the vessel or an explosion suppression system.sion
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.22 A01
- Issued
- May 24, 2010
- Abate by
- Jun 24, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
E101E200
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.22 A02
- Issued
- May 24, 2010
- Abate by
- Jun 24, 2010
E101E200
Recent events (2)
- — I (S)
- — Z (S)
1910.95 D01
- Issued
- May 24, 2010
- Abate by
- Aug 6, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
81108111
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.95 G01
- Issued
- May 24, 2010
- Abate by
- Aug 6, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
81108111
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.95 K01
- Issued
- May 24, 2010
- Abate by
- Aug 6, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
81108111
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.307 C
- Issued
- May 24, 2010
- Abate by
- Jun 24, 2010
- Penalty
- Initial $1,750 · Current $875 Reduced
E101E200
Recent events (2)
- — I (S) $875.00
- — Z (S) $1750.00
1910.145 C03
- Issued
- May 24, 2010
- Abate by
- Jun 24, 2010
E101E200
Recent events (2)
- — I (O)
- — Z (O)
1910.305 G01 I
- Issued
- May 24, 2010
- Abate by
- Jun 24, 2010
E101E200
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Bill Denoon Lumber Company DBA Clayco DRY Kiln
View Bill Denoon Lumber Company DBA Clayco DRY Kiln's full OSHA safety record →
More inspections in this industry (NAICS 321918)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 313156044.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.