Safety Incidents OSHA Severe Injury Reports · 2015–2025
2,004,209Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: NUCOR CASTRIP ARKANSAS, LLC

Referral inspection · Safety discipline

On , OSHA opened a referral safety inspection of NUCOR CASTRIP ARKANSAS, LLC in 6061 E STATE HWY 18, BLYTHEVILLE, AR 72315 (NAICS 331110). OSHA activity number 343296828.

Watch Nucor Castrip Arkansas, LLC — free Get an email when a new federal OSHA severe-injury report for Nucor Castrip Arkansas, LLC is published. One employer, no account, unsubscribe in one click.
Site address
6061 E STATE HWY 18
City
BLYTHEVILLE
State
AR
ZIP
72315
Mailing
6061 E STATE HWY 18, BLYTHEVILLE, AR 72315
Inspection type
Referral (C)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
331110
Employees
85
Ownership type
A

4 citations on file for this inspection.

1910.25 C02

Deleted Serious Gravity 10 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $9959.00 · Current $0.00 Reduced
29 CFR 1910.25(c)(2): The employer did not ensure standard stairs have a maximum riser height of 9.5 inches (24 cm).  On or about July 12, 2018 and times prior, the stair onto the work platform in the hot box and motor rolls' area had riser height of about 23 inches, exposing employees to trips and fall hazard.
Recent events (2)
  • — I (S) $0
  • — Z (S) $9959

1910.36 G02

Other-than-serious 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $2500.00
29 CFR 1910.36(g)(2): Exit access(es) were not at least 28 inches (71.1 cm) wide at all points.    On or about July 12, 2018 and times prior, the exit route into/out of the mill area where hot boxes and motors for the rolls were located was approximately 24 inches wide, which could cause entrapment and fall hazards during an emergency escape situation.
Recent events (2)
  • — I (O) $2500
  • — Z (S) $0

1910.37 B01

Deleted Serious Gravity 1 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $4268.00 · Current $0.00 Reduced
29 CFR 1910.37(b)(1): Each exit route was not adequately lighted so that an employee with normal vision can see along the exit route.  On or about July 12, 2018 and times prior, the employer did not ensure that the exit route into/out of the mill area where hot boxes and motors for the rolls were located was adequately lighted.
Recent events (2)
  • — I (S) $0
  • — Z (S) $4268

1910.147 C04 I

Other-than-serious 1 instance 3 exposed
Issued
Abate by
Penalty
Initial $19918.00 · Current $5000.00 Reduced
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section:    On or about July 12, 2018 and times prior, the employer did not provide employees performing maintenance/inspection of an x-ray gauge and opening hot box #2 a documented procedure that includes safe-pinning the opened lid of hot boxes. This condition exposed employees to caught-in and crushing hazards.    The Nucor Steel was previously cited for a violation of this occupational safety and health standard or its equivalent standard 1910.1479(c)(4)(i), which was contained in OSHA inspection number 1279003, citation number 1, item number 1 and was affirmed as a final order on March 19, 2018, with respect to a workplace located at Tuscaloosa, AL.
Recent events (2)
  • — I (O) $5000
  • — Z (R) $19918

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343296828.