OSHA Inspection: AMERICAN CUSTOM BUILDERS

Issued

2020-05-20 00:00:00

Abate by

2020-07-08 00:00:00

Penalty

Initial $325.00 · Current $325.00

General-duty citation text

29 CFR 1903.19(c)(1): The employer failed to certify to OSHA (the Agency) that each cited violation has been abated:  The Employer failed to certify that Citation 1 Items 1a, 1b, and 1c - 29 CFR 1926.304(f) and Citation 1 Item 1d - 29 CFR 1926.304(i)(1) have been abated.

Issued

2020-05-20 00:00:00

Abate by

2020-07-08 00:00:00

Penalty

Initial $325.00 · Current $325.00

General-duty citation text

29 CFR 1903.19(d)(1): The employer did not submit to the Agency documents demonstrating that abatement is complete for each willful or repeat violation and for any serious violation for which the Agency indicates in the citation that such abatement documentation is required:  The Employer failed to submit documentation demonstrating abatement is complete for serious violation Citation 1 Item 1a -  29 CFR 1926.304(f).

Issued

2020-01-09 00:00:00

Abate by

2020-01-15 00:00:00

Penalty

Initial $3978.00 · Current $3978.00

General-duty citation text

29 CFR 1926.304(f): Section 3.1.3(c) American National Standards Institute 01.1.1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  In applications (a circular hand-rip saw) where injury to the operator might result if motors were to restart after power failures, provisions were not taken to prevent machines from automatically restarting upon restoration of power:  Job Site - The Delta table saw was not equipped with a device to prevent it from automatically starting upon restoration of power after the loss of power.

Issued

2020-01-09 00:00:00

Abate by

2020-01-15 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1.1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Circular hand-fed rip saws were not equipped with a spreader to prevent materials from squeezing the saw or being thrown back on the operator:    Job Site - The Delta table saw, used for ripping, was not equipped with a spreader.

Issued

2020-01-09 00:00:00

Abate by

2020-01-15 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(c) American National Standards Institute 01.1.1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Circular hand-fed rip saws did not have  non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator:  Job Site - The Delta table saw, used for ripping, was not equipped with anti-kick back fingers.

Issued

2020-01-09 00:00:00

Abate by

2020-01-15 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(i)(1): Each circular hand-fed ripsaw was not guarded by a hood which completely enclosed that portion of the saw above the table and that portion of the saw above the material being cut:  Job Site - The Delta portable table saw, used for ripping, was not equipped with a hood guard.