PARAGOULD, AR —
OSHA Inspection: UTILITY TRAILER MANUFACTURING COMPANY
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of UTILITY TRAILER MANUFACTURING COMPANY in 2921 HWY 49 N, PARAGOULD, AR 72450 (NAICS 336212). OSHA activity number 346383714.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- UTILITY TRAILER MANUFACTURING COMPANY
- Site address
- 2921 HWY 49 N
- City
- PARAGOULD
- State
- AR
- ZIP
- 72450
- Mailing
- P.O. BOX 1606, PARAGOULD, AR 72450
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336212
- Employees
- 900
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Jun 9, 2023
- Abate by
- Feb 21, 2025
- Penalty
- Initial $15,625 · Current $16,131
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1) The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to struck-by hazards. (a) On or about December 10, 2022, the employer did not provide specific written instructions and communicate hazards to employees performing service and maintenance on a Southworth Scissor-Lift Table. One feasible and acceptable means of abatement would be to adequately label and communicate all applicable energy sources for the Southworth Scissor-Lift table to employees.
Recent events (3)
- — F (S) $16131
- — C (S) $15625
- — Z (S) $15625
1910.147 C04 II B
- Issued
- Jun 9, 2023
- Abate by
- Jun 29, 2023
- Penalty
- Initial $11,162 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(B): The energy control procedures did not clearly and specifically outline the steps for shutting down, isolating, blocking and securing machines or equipment to control hazardous energy. a) On or about December 10, 2022, at the axle line, employees were performing servicing and maintenance activities on the lift table comprised of components including, but not limited to a roller conveyor and Southworth LS lift table; and the energy control procedure did not have outlined steps for isolating all sources of hazardous energy.
Recent events (3)
- — F (S) $0
- — C (S) $11162
- — Z (S) $11162
1910.147 C04 II C
- Issued
- Jun 9, 2023
- Abate by
- Jun 29, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(C): The energy control procedure did not clearly and specifically outline the steps for placement, removal and transfer of lockout devices or tagout devices and the responsibility for them: a) On or about December 10, 2022 , at the axle line, employees were performing servicing and maintenance activities on the lift table comprised of components including, but not limited to a roller conveyor and Southworth LS lift table; and the energy control procedures did not have procedures for affixing and removing locks on the electrical energy sources.
Recent events (3)
- — F (S) $0
- — C (S) $0
- — Z (S) $0
1910.147 C04 II D
- Issued
- Jun 9, 2023
- Abate by
- Jun 29, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(D): The energy control procedures did not clearly and specifically outline the requirements for testing a machine or equipment to determine and verify the effectiveness of lockout devices, tagout devices, and other energy control measures: a) On or about December 10, 2022, at the axle line, employees were performing servicing and maintenance activities on the lift table comprised of components including, but not limited to a roller conveyor and Southworth LS lift table with energy sources such as, but not limited to hydraulic, electrical, and mechanical. The procedures did not include specific steps to verify the effectiveness of the energy control measures.
Recent events (3)
- — F (S) $0
- — C (S) $0
- — Z (S) $0
1910.147 C05 I
- Issued
- Jun 9, 2023
- Abate by
- Jun 22, 2023
- Penalty
- Initial $15,625 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(5)(i): Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware were not provided by the employer for isolating, securing or blocking of machines or equipment from energy sources: (a) On or about December 10, 2022, employees were performing servicing and maintenance on a lift table comprised of a roller conveyor and LS Series lift table by Southworth. Hardware was not provided to secure and/or block the upper portion of the lift table loaded with the roller conveyor.
Recent events (3)
- — F (S) $0
- — C (S) $15625
- — Z (S) $15625
More inspections at Utility Trailer Manufacturing Company
View Utility Trailer Manufacturing Company's full OSHA safety record →
More inspections in this industry (NAICS 336212)
More inspections in AR
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346383714.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.