Stella-Jones Corporation

The injured employee was assisting a skid steer operator to move a stack of bundled railroad ties. The operator lifted the stack of bundled ties and the band securing the bundle broke, causing the ties to fall and strike the injured employee. The injured employee sustained a fractured hip and both ankles were fractured.

An employee was trying to clear a jam of wood debris (cut-offs) at a transition between a flat belt and a shaker-conveyor. When the employee grabbed a cut-off, it caught the belt and wedged the employee's left index finger between the belt and the shaker-conveyor surface. The finger was amputated. The machine was unguarded at the time of the incident.

An employee was sharpening peeler blades when their shirt was caught in the grinding wheel. The employee sustained tendon damage and a crushed right hand.

An employee was pre-drilling holes in ties on which to set plates and spikes. As the employee pulled the hand drill from a guide hole, the drill caught his pant leg. The drill then went into the right side of his left foot, resulting in a laceration that required hospitalization.

A temporary employee was tacking end plates onto a railroad tie by hand. They reached over to the press that completes the attachment of the end plate after the rail tie crosses over a limit switch. The limit switch activated, resulting in a crush injury to the employee's left index and middle fingers that required medical amputation. The machine was guarded at the time.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee was re-lighting a fire in a wood waste boiler using diesel fuel when the diesel flashed and caused second-degree burns to their hands.

An employee was working from a step ladder and putting grease in a fitting on a cylinder door. His leg was caught between two of the ladder's rungs and the ladder folded up. He fell and broke his leg.

On June 10, 2024, an employee was grinding mulch in a tub grinder. A front end loader was unloading mulch into the tub grinder and ran over his ankle, breaking it and also causing a hairline fracture to his pelvis. He was hospitalized, requiring surgery.

On January 17, 2024, an employee was working on a roller machine when a piece of metal lacerated their right forearm, causing tendon injury. The employee was hospitalized and underwent surgery.

An employee had been warming his hands at a stationary heater near the stacker operator. He was by the rear passenger-side of his parked forklift when another forklift reversed and struck him. His left leg was pinned between the two forklifts and he sustained a fractured fibula.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.