JMC Steel Group

An employee was working on a pipe-threading machine, placing caps on the end of a pipe. The employee's finger caught the sharp edge of the pipe and was severely lacerated. The employee was hospitalized.

An employee was burned on his lower back and posterior by a heater used to warm equipment and the general environment. He was wearing personal protective equipment.

An employee suffered a laceration and burn injury to his left cheek while maneuvering a 20-foot-long, 3/4-inch-diameter pipe from the sizing mill area to the hot rack with a mechanical lifting/maneuvering device. The employee was hospitalized for treatment.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.