Zenith Tech, Inc.

An employee was loading an excavator onto a lowboy trailer. The employee's hand slipped while securing the thumb/bucket and the bucket fell on the employee's hand, crushing the fingers.

An employee suffered third degree burns on the back and lesser burns in the armpit area while torch cutting on a bolt.

Employees were stripping concrete forms from a bridge when a 4 x 8 piece of plywood fell hitting another employee on the ground causing broken ribs, a back injury, and a punctured lung.

An employee was injured when bridge piling fell on his leg during highway construction work.

An employee was directing traffic when a shag truck turned sharply and ran over the employee. They suffered a crush injury to the lower left leg and internal bleeding.

An employee was standing on the street holding a stop/slow paddle and directing the flow of traffic. As they were holding the stop sign, a vehicle attempted to drive around the employee but struck them. The employee sustained fractures to the tibia and fibula and was hospitalized.

A paving crew was working on a roadway when a motor vehicle entered the work zone. Two employees sustained injuries including fractures and damage to internal organs that required hospitalization.

An employee was flagging traffic when they were struck from behind by a car that entered a work zone. The impact of the vehicle threw the employee approximately 45 feet and she landed on another employee. The employee who was struck by the car sustained a head laceration and fractures to the ribs and ankle.

An employee was setting up a worksite on a roadway when they were struck by a vehicle. The employee suffered blunt force trauma to the chest, pelvis, and legs from contact with the vehicle, with subsequent trauma to the neck and head upon falling to the ground.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.