Pleasant River Lumber

A saw was being swapped out. The retaining pin caught on the inside of the saw stack, which caused slack in the lifting device being used to lower the pin into place. The pin then dislodged and struck an employee's right index finger. The last joint of the finger was amputated.

An employee was measuring the thickness of boards on a conveyor belt. As the employee reached for a board, their hand was pulled into the conveyor belt, resulting in a fractured index finger that required hospitalization and surgery, as well as bruises to additional fingers.

An employee was attempting to free a jammed board in a sorter bin. The bin arm cycled and pinched the employee's left thumb causing a partial amputation.

An employee was stacking lumber and the lumber pinched their finger against a back stop. The employee sustained an amputation to a fingertip.

An employee was drying and finishing vehicles when a vehicle door closed on their left middle fingertip and amputated it.

An employee was climbing down from a tractor trailer bed when they lost their footing and grabbed onto the roll-up door to stop the fall. The roll-up door then fell onto the employee's hand, resulting in a hand fracture that required surgery.

An employee was attempting to remove a tarp from a flatbed trailer when the trailer handle struck the employee in the chest, resulting in two broken ribs and a punctured lung.

An employee was near a backhoe while the operator was getting a broom. The broom handle struck the lever that actuates the swing of the backhoe bucket. The bucket then struck the injured employee, pinning him to the outrigger. The employee suffered crush injuries to the chest.

The injured employee was being trained on loading trucks in the load out bay. The injured employee and his supervisor climbed the stairs that run parallel to the truck and trailer, walked to the upper platform used for observation and sample taking, and saw that the lid of the grain trailer was closed. The employees began working to open the lid which appeared to be stuck due to cold weather. The injured employee pulled on one of the pivot arms that connect the lid to the main body of the trailer. As the lid began to open, the employee s right hand slipped down on the pivot arm and his index finger was caught between the pivot arm and the base of the pivot arm. The employee s right index finger was fractured and three nerves were severed. The employee was hospitalized.

An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.

An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.

An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.

An employee was working to get a log back onto a carriage. The employee came into contact with the running saw, which amputated their arm.

While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.