Woodland Pulp LLC

An employee slipped while getting off a flatbed truck. His left ring finger was caught on the truck and amputated.

Employees were restarting a digester after an acid cleaning. Hot liquor (300 degrees) was being introduced into the digester, but the valve to the acid tank was not closed, so hot liquor entered the acid tank and caused the lid on the fiberglass tank to blow. The hot liquid from the tank showered the injured employee, who suffered burns to the top of his head and was hospitalized.

An employee was servicing a heater when his right hand was caught in an inclined conveyor adjacent to the heater. The employee suffered a finger amputation on the right hand.

An employee connected a steam line to a hose to clean equipment when the fitting broke loose. They were struck by steam in the left inner thigh, resulting in burns that required hospitalization.

An employee was straining hot water from a pot of rice when the water splashed onto them, resulting in burns to their chest, arms, shoulder, and back.

An employee was making tea when she noticed tea grinds were collecting on the side and water was no longer dripping through the funnel. The employee was checking the funnel when boiling water and tea grinds spilled onto the left side of her body. The employee sustained burns to her neck, back, and arm.

An employee had turned off the ball valve on a waterpipe system and was removing the plug when the coupling system attached to the strainer came apart. Hot water sprayed on his arm and back, resulting in first- and second-degree burns that required surgery.

An employee was using a shovel to remove waste vermiculite from molten zinc. The metal had been placed in a bin and partially hardened. The employee broke through the partially hardened metal; still-molten metal flowed to the employee's steel-toed right boot and entered through the cloth boot tongue. The employee suffered a third-degree burn to the right foot and was hospitalized.

An employee was loading black liquor into a tanker truck using a swivel arm. The arm caught and pinched his right middle finger as it moved, resulting in a partial amputation to the first knuckle.

An employee was visually inspecting the drive line for a conveyor. There was an explosion in the conveyor, and the employee suffered second- and third-degree burns to both forearms.

An employee was driving forklift with a load when the forklift hit a guardrail and the employee fell to the ground, resulting in a broken elbow, broken shoulder, and lacerations.

An employee was putting a chain back on a sprocket. The gearbox and sprocket contained two drive chains connected to the lowerator (vertical conveyor) and counterweight assembly. The employee received an alarm indicating that one of the chains had gone slack. While the employee was putting the chain back on the drive sprocket with tongue and groove pliers, the weight of the chain and counterweight fell back in place on the sprocket, pulling the employee's left hand into a pinch point. The employee's ring fingertip was amputated up to the fingernail.

While troubleshooting equipment, an employee tripped on the turntable of the conveyor system and fell to the floor, fracturing their right femur.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.