Zachry Industrial, Inc.

An employee was walking on site when he tripped on a wooden survey stake that was lying flat on the ground. He fell into another employee and sustained a fracture to the tibia/fibula.

An employee was working on top of a rebar mat that was about 4 feet off the ground. As he walked across the mat, he stepped into a gap and his lower leg was caught in the rebar. His right leg twisted, and he suffered fractures to the tibia and fibula. He was hospitalized.

A Zachry Industrial employee was pushing a cart up a walkway. A forklift struck the employee as it finished turning around, its back right wheel hitting the employee's left foot and causing multiple fractures.

An employee was welding the bottom of a chute on the underside of a bin. Hot material came through a small gap between a gate inside the bin and the chute, contacting the employee below. The employee received second and third burns to the neck.

An employee was working to fit two 1-1/2-inch stainless steel spool pieces at a flanged connection to bolt up. To align the two spool pieces, the top section of pipe (10 feet in length) was rigged using a nylon strap choker, attached to a 1/2-ton chain. As the employee attempted to move the pipe, the load shifted in the nylon strap, causing the top section of the pipe to drop approximately 1-2 inches, which pinched the injured employee's left index finger in the flanged connection and resulted in an amputation of the finger's distal tip.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee fell while stepping off the tailgate of a pickup truck. The employee landed on the ground and suffered a broken left fibula and tibia.

On October 7, 2025, employees were conducting trenching operations for the installation of a new sewer line system. The excavator's bucket was detached and put inside the trench as it was being exchanged for a different-sized bucket. An employee entered the trench with a shovel to move some dirt located at the front end of the pipe. The excavator bucket shifted and slid, striking the employee s right foot and trapping it against the ground. The employee sustained a fractured right tibia.

Employees were working to dislodge a large truck that was stuck in a rut using tow straps and a front-end loader with the bucket removed. An employee connected the straps to the loader and truck and another employee slowly engaged the loader to close the coupler. The injured employee's arm became caught in a pinch point. The employee was hospitalized with a fractured arm.

An employee was lifting a piece of 30-inch line stopping equipment using a jack screw. A lifting eye weld snapped and the load dropped. The end of the jack screw then landed on the employee's heel and crushed it. The employee was hospitalized.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.