Western Construction, Inc.

Two contractor employees were working with customer personnel to install 6" blind skillets between a natural gas valve and flange couplings. While attempting to spread flange couplings apart to install the blind skillet, gas began leaking from the flange separation. A contractor employee attempted to seal the leak by pumping grease into the 6" valve fitting using a battery-operated grease gun. While doing so, the escaping gas ignited and the fire engulfed the workers. One employee was hospitalized for burns to the arms, face, and the back of their neck.

An employee was using a scraper to clean debris from an asphalt paver when his safety vest became caught on the paver and he was pulled in toward the auger. He was hospitalized with second and third degree burns from the mid-torso to the armpit. The paver was running at the time of the incident.

An employee was working with a rotomill machine on the ground checking asphalt depth. The employee used his foot instead of the air wand to remove excess. He caught his foot in the rotomill track injuring the right big toe. A physician amputated bone to close the wound.

An employee connected a steam line to a hose to clean equipment when the fitting broke loose. They were struck by steam in the left inner thigh, resulting in burns that required hospitalization.

An employee was straining hot water from a pot of rice when the water splashed onto them, resulting in burns to their chest, arms, shoulder, and back.

An employee was making tea when she noticed tea grinds were collecting on the side and water was no longer dripping through the funnel. The employee was checking the funnel when boiling water and tea grinds spilled onto the left side of her body. The employee sustained burns to her neck, back, and arm.

An employee had turned off the ball valve on a waterpipe system and was removing the plug when the coupling system attached to the strainer came apart. Hot water sprayed on his arm and back, resulting in first- and second-degree burns that required surgery.

An employee was using a shovel to remove waste vermiculite from molten zinc. The metal had been placed in a bin and partially hardened. The employee broke through the partially hardened metal; still-molten metal flowed to the employee's steel-toed right boot and entered through the cloth boot tongue. The employee suffered a third-degree burn to the right foot and was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.

Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.

A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.

An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.

An employee tripped over a bin and fell to the floor. She landed on her hip and braced herself with her arm, resulting in a fractured hip and wrist.

An employee was diagnosing the lack of flow of product to a powder bin. The employee removed the rotary star valve below the bin. While he was reinstalling the valve, his right middle finger was crushed between its shaft and its housing. The finger was partially amputated.

An employee was standing on a multi-purpose ladder installing head flashing over a window. Their feet were approximately 6 feet off the ground and three rungs from the top. The employee lost their grip on the drill they were using and the ladder tipped over. The employee fell from the ladder to the ground, resulting in a fractured left wrist, bruised chest, and lacerations to their face and lip.

An employee was inspecting the overhead area of a single-person lift and repositioning the lift through a double doorway. As they were transitioning through the doorway, they were caught between the doorframe and the vertical mast of the lift. The employee was hospitalized with injuries to the nose, left maxillary sinus, left orbital bone, and left jaw, with fractures at the maxillary sinus area.

An employee was loading a 4-inch wooden door into a pickup truck when he felt a pop in his right side behind his shoulder blade. He was hospitalized later that day and underwent surgery, having suffered a collapsed right lung.