Pedestrian struck by forward-moving vehicle in work zone · Soreness, pain, hurt-nonspecified injury
At a glance
Federal OSHA recorded a severe workplace injury
at ROBERTSON CONTRACTORS, INC., Intersection of South County Rd. 57 & Highway 77, DYESS, ARKANSAS 72330
on — Soreness, pain, hurt-nonspecified injury, affecting the leg(s), unspecified.
Final narrative
An employee was washing out a concrete bucket beside the guardrail of a bridge when a concrete delivery truck struck and pinned him between the left front side of the concrete delivery truck and the bridge guardrail. The employee sustained an injury to his right leg and was hospitalized.
An employee was walking in a construction area to retrieve a grinder and his tools when a rolled false form collapsed, causing a generator, wood forms, and the employee to fall about 16 feet to the level below. The generator struck the employee's lower leg during the fall, fracturing it. The employee was hospitalized and required surgery to their tibia.
An employee was handling a 30-pound tube block to place on a trailer bed. In an attempt to keep the tube block from falling, his right thumb was caught between the tube block and the bed of the trailer, resulting in a right thumb tip amputation.
On 5/21/2018, an employee was inside an aerial lift and raising it when the employee's right hand became pinched, causing a laceration that resulted in a right pinky finger amputation.
An employee was directing traffic when a shag truck turned sharply and ran over the employee. They suffered a crush injury to the lower left leg and internal bleeding.
An employee was standing on the street holding a stop/slow paddle and directing the flow of traffic. As they were holding the stop sign, a vehicle attempted to drive around the employee but struck them. The employee sustained fractures to the tibia and fibula and was hospitalized.
A paving crew was working on a roadway when a motor vehicle entered the work zone. Two employees sustained injuries including fractures and damage to internal organs that required hospitalization.
An employee was flagging traffic when they were struck from behind by a car that entered a work zone. The impact of the vehicle threw the employee approximately 45 feet and she landed on another employee. The employee who was struck by the car sustained a head laceration and fractures to the ribs and ankle.
An employee was setting up a worksite on a roadway when they were struck by a vehicle. The employee suffered blunt force trauma to the chest, pelvis, and legs from contact with the vehicle, with subsequent trauma to the neck and head upon falling to the ground.
More severe injuries in this industry (NAICS 237310)
An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.
An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.
An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.