Carpenter Technology Corporation

An employee was walking across a foot bridge at the workplace. They rolled their right ankle on the transition between the bridge and the ground and fractured it.

An employee was working at the strip metal processing machine (wet (oil) process). The employee used a rag in their right hand to clean a roller and three fingers were caught in a nip point, resulting in amputation of their right thumb tip as well as their index and middle fingertips. The machine was not guarded and running at the time.

An employee was performing a head change on the bar turner machine when the pinch rolls closed and the bar lifted, pinching the injured employee's left index finger between the bar and the rest. The employee sustained a fingertip amputation.

The injured employee was operating a straddle carrier to transfer a load to the billet yard. When they turned left into the billet yard, the straddle caught fire. The employee stopped the vehicle and jumped approximately 6-8 feet to the ground. The employee sustained first- and second-degree burns to the head, face, and arms, and a fractured right leg.

An employee was preparing to move a 2,800-pound mold using a sling lifting chain and overhead crane to insert a mold plug. Once the end of the mold was 12 to 16 inches from the floor, the employee stopped the crane and moved to insert the mold plug into the mold. The mold slipped out of the chains onto the employee's left foot, causing crush injuries to the first and second toes. The employee was hospitalized.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

An employee used a crane to set down a bar. The bar measured 9 inches by 16 feet. The strap got stuck under the bar, and the employee asked another employee to jog the roll. The bar rolled and pinched the injured employee's left hand, resulting in a fingertip amputation.

An employee was loading a steel forming machine with steel to be processed. He went to move a cooling hose out of the way and his left thumb was crushed by the forming roller, resulting in injuries that required surgical amputation.

An employee was advancing a rail to line up for welding with a secondary rail on the weld line when his right middle and ring fingers were caught between the rails. The employee sustained an amputation to the top knuckle of the middle finger and a fracture to the ring finger. The machine was guarded at the time.

An employee was working near molten metal and experienced heat illness symptoms including cramps. The employee was hospitalized.

An employee was preparing bundles of 24-foot square metal tubing to be loaded onto a truck and cut the safety band for a bundle. While the employee was removing a piece of dunnage from a bundle, they bumped the bundle with their leg. The metal tubing then fell forward and struck the employee, causing a fractured left ankle.

An employee was closing a door when the door closed on their right index finger, resulting in a fingertip amputation.

An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.

An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.

An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.

An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.