Felker Brothers Corporation

An employee was sanding the head of a stainless steel chisel when the employee's right thumb became caught between a vertical belt sander and the work rest, causing an abrasion that resulted in a partial amputation to the thumb tip.

On August 9, 2018, an employee was using an electric grinder to remove the welds from an elbow fitting that was strapped to a welding fixture when the elbow fitting kicked back and his fingers were pinched between the elbow and welding fixture, resulting in right index and middle fingertip amputations.

An employee was checking the function of newly installed actuators when they were struck by a pressurized release pipe. The employee suffered fractures to the orbital socket and shoulder, requiring hospitalization.

A ramp in the trunk of a delivery van struck an employee's calf. She suffered a broken leg and was hospitalized.

An employee was completing a service call and looking at a water pump when the pump cover plate struck their forehead. The employee sustained a forehead laceration and fracture requiring hospitalization.

An employee was removing chains from a steel tube. A sorting hook attachment was caught on the staging area cross member. When he raised the chains, the sorting hook snapped back and struck the employee's face causing a fractured jaw.

An employee was in the sawmill basement using a push broom and shovel to clean wood chips and sawdust. The employee's right arm was struck by a wooden board between the wrist and elbow, resulting in a fracture.

An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.