MERCURY MARINE

An employee was assembling the gearbox of a lower unit (of a boat motor). They used a handheld electric drill to power the lower unit's gears and inspect the assembly. A gear was out of tolerance, so the employee placed sandpaper in the gearbox to remove any burrs or other material. The employee activated the drill and their left middle finger contacted a nip point between the gears in the unit, resulting in a fingertip amputation.

An employee was walking in the racking area to check parts when they were struck by an oncoming forklift. The front wheel ran over the employee's right leg, resulting in fractures to the leg and ankle.

On January 28, 2022, an employee was removing an extra bar of steel stock that was fed into a bar stock feeder. The bar of steel stock fell approximately 1 inch onto the employee's left ring finger, resulting in a partial amputation.

An employee was pushing an electrical pallet jack loaded with parts baskets. While going through a doorway, the parts baskets caught the door frame and fell back onto the employee, who suffered fractures to the skull, cervical vertebrae, and ribs, as well as an ankle injury.

An employee was tossing a damaged toilet into a compactor. The toilet bounced off the compactor and lacerated the employee's right wrist, cutting an artery and tendon.

An employee was operating a hydraulic jack to bend a frame when the jack came loose and struck the employee. They were hospitalized for a spleen injury.

A truck had been towed into the shop with a flat tire and a blown airbag. An employee checked the tire for damage and was airing the tire. The employee was installing the valve core when the bead slipped off the rim. Air escaped, and the aluminum wheel struck the employee's head and face. The employee became unresponsive and was bleeding.

On December 14, 2023, at 8:40 p.m., three employees were inspecting milling machines for startup. A few of the sleeves on the mill drum needed to be changed out. The injured employee was trying to input a sleeve on the mill drum using a hammer. The hammer hit the edge of the drum, which caused a metal piece to splinter off and strike the employee's cheek just below the left eye. The metal splinter embedded in the back of their eye socket, resulting in pain, swelling, and bleeding that required hospitalization.

An employee was pushing a line of carts into a vestibule when the door cable snapped and struck his right ankle. The employee suffered a fracture that required surgery and hospitalization.

An employee was moving a hoist to the end of a bridge rail to create space for another hoist on the same rail. The hoist being moved, along with its supporting beam, detached from the bridge rail and fell, striking the employee in the head. He suffered a contusion and laceration to the head and was hospitalized.

An employee was operating a machine. When they performed a motion to push a machined engine block away from their body, they experienced a back strain, resulting in hospitalization.

On September 13, 2025, an employee had been working at an outdoor event. At the end the day, she was walking around outside the facility to make sure everything was put away and felt overheated. The employee was hospitalized for heat-related illness.

An employee was installing insulation in a wall panel when the panel fell on top of them, resulting in leg and back injuries that required hospitalization.

An employee put a cylinder machining pallet into manual mode to unjam it. After completing the task, their left hand became lodged between a pulley and belt, resulting in the amputation of three fingers.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.