Struck by object falling from vehicle or machinery-other than vehicle part · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Barko Hydraulics, LLC, One Banks Avenue, SUPERIOR, WISCONSIN 54880
on — Fractures, affecting the lower leg(s).
Final narrative
On July 12, 2017, an employee was using a wrench to remove a line plug from a hydraulic cylinder while it was resting in a wooden cradle (block) on top of a machine's sub-frame. The wrench breaking the line plug loose created a jarring motion that caused the 620-pound hydraulic cylinder to shift and fall (3.5 feet) off the elevated surface and onto the employee's lower leg, fracturing the right tibia. The employee was hospitalized.
HospitalizedLower leg(s)Vehicle and mobile equipment parts, n.e.c.
An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.
An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.
An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.
An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.
More severe injuries in this industry (NAICS 333120)
An employee was working behind a stack of steel I-beams (stacked 2 columns deep and 4 levels high on the floor) while a forklift was pushing the stack. When the forklift took off the second-to-last beam, the last one was pushed over, causing it to fall to the ground and strike the employee. The employee sustained a fracture to the right leg.
An employee was lifting a flat sub (sheet steel) in the flats robot cell (weld area). He was operating a hoist when his left little fingertip got caught between the lifting device hook and the flat sub. The employee sustained a partial transphalangeal amputation.
An employee was underneath a 35-foot boom truck and adjusting the transmission linkage when the truck jumped over the wheel chocks and rolled over the employee's right leg, resulting in a fracture.
A crane was being used to lift a debris tank from a rack. The tank crushed the employee's right hand, causing amputations to the employee's right ring finger and little fingertip.
An employee was removing a small sheet metal part out of the die of the brake press. The foot pedal was pressed, causing the part to lift and crush their left thumb against the die. The employee suffered an amputation to the thumb tip including the loss of flesh and the fingernail.
The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.
An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.