HACKNEY LADISH, INC.

An employee was setting up their workstation and aligning parts to be shotblasted. While the employee was moving a hose, a 12-by-8-inch pipe fitting became unstable and fell, striking the employee's leg above the knee. The employee was sitting in a chair and they sustained a femur fracture.

An employee was installing a hydraulic cylinder when it slipped and fell. His right little finger was caught under it and the fingertip was amputated.

An employee was sizing a T in a die using a hydraulic press. His hand slipped and the die closed on his left pinky finger.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee was troubleshooting a shell core machine that had failed to raise the sand hopper into place for core making. The employee went to manipulate a switch and the machine cycled. The employee s left middle fingertip was caught between the roller-ball switch and the roller-ball switch target, resulting in a laceration that required surgical amputation to part of the distal phalanx.

On August 18, 2025, at approximately 7:40 AM, an employee utilized a pocket knife to cut banding on a new bundle of rod material. The knife blade bent during use. The employee was working to straighten the blade on a hard surface when the knife slipped, causing a lacerating their right wrist/forearm. The employee was hospitalized.

An employee was manually pulling drive belts to rotate a machine that needed repair. The employee's right index finger was pinched between a rubber drive belt and a pulley, causing an amputation to the fingertip.

At about 9:15 a.m. on May 14, 2025, an employee was using a bending press to bend metal into a U shape. The press caused an amputation to the employee's left middle finger.

An employee was running a test pipe for 12 feet and went to pull the pipe out of a roll grooving tool. As he was doing this, the tool's control pedal actuated, causing the tool to rotate. The employee's glove became caught and was pulled into the rollset, amputating about half an inch of his index finger.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.