KHS USA, Inc.

An employee was feeding a borescope camera into the inlet port of a liquid ring vacuum pump to take internal pictures. The camera was passing through a ball valve when the valve closed on his finger and the borescope. The employee sustained a fingertip amputation.

An employee connected a steam line to a hose to clean equipment when the fitting broke loose. They were struck by steam in the left inner thigh, resulting in burns that required hospitalization.

An employee was straining hot water from a pot of rice when the water splashed onto them, resulting in burns to their chest, arms, shoulder, and back.

An employee was making tea when she noticed tea grinds were collecting on the side and water was no longer dripping through the funnel. The employee was checking the funnel when boiling water and tea grinds spilled onto the left side of her body. The employee sustained burns to her neck, back, and arm.

An employee had turned off the ball valve on a waterpipe system and was removing the plug when the coupling system attached to the strainer came apart. Hot water sprayed on his arm and back, resulting in first- and second-degree burns that required surgery.

An employee was using a shovel to remove waste vermiculite from molten zinc. The metal had been placed in a bin and partially hardened. The employee broke through the partially hardened metal; still-molten metal flowed to the employee's steel-toed right boot and entered through the cloth boot tongue. The employee suffered a third-degree burn to the right foot and was hospitalized.

An employee was moving a stand-up powered industrial truck from a warehouse to a service area. During a turn on a slight decline, the vehicle's steering chain broke and the vehicle spun. The employee fell off the vehicle and landed on his right knee, breaking his fibula.

An employee had just driven a forklift onto a trailer and was stepping down from the forklift cab onto the trailer bed. He stepped onto a chain/buckle system (used to secure the forklift to the trailer bed during travel) and fell from the deck. He suffered a head laceration and two broken vertebrae and was hospitalized.

The injured employee was leaving to go to lunch when he and another employee tried going through the office door at the same time. The employees bumped into each other and the injured employee lost his balance and fell to the ground. He was hospitalized with a broken hip.

An employee was pushing mailers when the arm/knife of a picking counter machine caught their hand. The employee suffered the amputation of their right middle finger above the knuckle. The machine was not sufficiently guarded.

An employee was using a belt sanding machine to put a 45-degree angle on the end of a metal flat-bar (1"W x 24"L x 3/8"T). The flat bar was caught between the tool-rest and the belt, causing the opposite end of the flat bar that the employee was holding to spring back toward the machine. Their left hand struck the belt/machine guard resulting in amputation of 3/4 of their little finger. Their ring finger was also lacerated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.