Bennett Steel, Inc.

An employee was returning from lunch and was climbing a 12-foot extension ladder set up on the second floor to access the roof of the second floor. The employee fell approximately 8-9 feet to the floor and was hospitalized with fractured feet.

An employee was operating a crane with a wireless remote to move a steel beam in order to paint the bottom of the beam. The beam was set on saw horses. The employee clamped on the beam. The beam fell off the saw horses and landed on the employee's legs. The employee got pinned between the beam and a trailer that was behind him, where beams would be loaded after painting. The employee suffered two broken bones in their left leg below the knee and one broken bone in their right leg.

An employee was moving a piece of an I-beam for welding when it rolled off the cribbing. The employee went to catch it when it fell and crushed the employee's finger, resulting in a partial amputation.

An employee was helping to disassemble large reels used to store steel wire when a 264-pound flange from the reel fell over onto the employee's left leg. The employee sustained multiple fractures to their leg and ligament injuries to the lower leg.

The injured employee was putting away materials on the warehouse floor as a co-worker was pushing a pallet onto a nearby shelf. The pallet knocked another pallet forward, causing it to fall onto the injured employee's shoulders. The employee suffered fractures in their right and left knees and ankles.

Employees were moving a single man lift into a building and reclining the lift to position it to fit through the door. The lift shifted and fell, causing the employee to sustain fractures to the left tibia and fibula. The employee was hospitalized and had surgery.

An employee was moving a light tower so it could be hitched to a truck. He grabbed the tongue of the trailer hitch on the light tower to slide it to the left. The tongue jack fell off, causing the light tower tongue to drop on the employee's right hand. The employee's middle fingertip was amputated.

An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.