Compressed or pinched by shifting objects or equipment · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at TETRA Technologies Inc., 700 Millers Run Road, CUDDY, PENNSYLVANIA 15031
on — Fractures, affecting the leg(s), unspecified.
Final narrative
An employee was holding a 55-gallon drum in place with his right leg while another employee was attempting to puncture the drum with the forks of a forklift. As the forklift operator applied pressure to the drum with the forks, the injured employee's foot became pinned to the ground under the drum, resulting in a fracture to his right leg. He was hospitalized and had surgery.
On July 22, 2023, an employee was swinging a 5-ton hammer on a hammer union. The employee then noticed a piece of metal was lodged in his upper left thigh and required hospitalization.
On 6/20/2023, an employee was opening a water faucet valve at a facility when they were stung by a wasp and experienced a severe allergic reaction. The employee was hospitalized.
An employee used a wire brush to clean the threads of two 10-foot joints of 2-inch figure 1502 iron pipe, which were sitting on the rack of a monorail trailer. As the employee rotated the pipe inward to clean the threads of the innermost joint, the opposite end of the pipe dislodged from the rack and fell to the ground. As it fell, the end nearest to the employee levered upward and pinched their right thumb between the two joints of pipe. The employee sustained a laceration and fracture to the thumb.
An employee's socks became wet while pressing on sand bags, which caused extreme blistering and skin around the area to turn black, resulting in a right toe amputation.
Two employees were transferring rinsate from a chemical tote to frac tanks using a bucket. Approximately six hours later, both employees stated that they felt winded with slightly strained breathing. One of the employees was hospitalized due to strained breathing and low oxygen levels.
An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.
An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.
An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.
During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.
An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.
More severe injuries in this industry (NAICS 213112)
An employee had been cleaning the work area. While lifting a saw, the employee's index finger was lacerated by the saw blade. A tendon was cut and required surgery.
An employee was delivering home heating fuel when bees came from the ground and stung the employee's face, neck, torso, and hands. The employee proceeded to shut off the oil flow before losing consciousness. They were hospitalized due to an anaphylactic reaction.
An employee was using a torch to loosen a bolt on a water trailer. Natural gas was present in the water and it ignited, causing a fire. The employee sustained third-degree burns to their upper leg.
An employee had been conducting crane operations. The employee went to stop a piece of oil and gas equipment for tubular running from falling over to the ground. Their right hand was caught between a rolling ladder and the equipment, resulting in fractures to the index and middle fingers. They were hospitalized and the middle finger required surgery.
An employee was working to install a drive belt on a water pump. He was holding the belt on both sides of the pulley, working to route it over the top. As he pulled down with his right hand, the pulley rotated and the belt slid over it, pulling his left little finger between the pulley and the belt. He suffered an amputation to the fingertip as well as a fracture to the ring finger.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.
An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.
An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.