Cianbro

An employee was using a 3-foot pry bar to lift a 3/8-inch piece of sheet of metal to remove the 3/4-inch wooden support blocks from underneath. The 3-foot pry bar slipped while the employee was removing the 3/4-inch wooden block, allowing the sheet metal to drop onto and amputate the employee's left index fingertip.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee was fixing a broken purlin at a worksite when they fell from the framing to the concrete floor approximately 19 feet below. The employee sustained brain bleeding and fractures to their face, vertebrae, and wrists.

Employees were removing scaffolding that was used to repair an ion exchange tank. The line was undergoing the regen process when a piece of scaffold struck a PVC pipe that transported hydrochloric acid (HCl). The injured employee was placing material inside a scaffold rack when he was sprayed in the face with HCl and sustained chemical burns to his eyes, face, chest, right arm, and left leg.

An employee was moving a ramming machine to a staging area. While using the controls on the side of the machine, there was a sudden heavy rainfall causing the equipment to slide. The ramming machine tipped over and caught the employee against the ground. The employee sustained a fracture to the right side of their pelvis and was hospitalized.

The injured employee was training a new employee on a dough machine. She went to show where the batter comes from and her right index fingertip was cut. The employee sustained an amputation to the fingertip. The machine was not guarded at the time of the incident.

An employee was operating a roller machine on a dirt slope when the machine hit a bump and fell onto it's side. While trying to get free of the falling machine, the employee's legs were pinned by the top bar of the cage. The employee was hospitalized and his left leg was amputated. He also sustained fractures to a hand and finger.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.