CATERPILLAR

An employee was installing a machining center when the employee's right index fingertip was amputated by a ball screw on the machining center's horizontal axis.

While moving a lower power train brake assembly with an overhead crane/lifting device, an employee's left thumb was pinched and amputated in a pinch point.

An employee was running a deflashing machine. The main auger of the machine registered a fault. The employee cleared the alarm and vacuumed out the media. He reached into the auger to clear the media by hand. The machine was running at the time. His right hand made contact with the moving auger, resulting in a partial amputation of his middle finger.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee was working behind a stack of steel I-beams (stacked 2 columns deep and 4 levels high on the floor) while a forklift was pushing the stack. When the forklift took off the second-to-last beam, the last one was pushed over, causing it to fall to the ground and strike the employee. The employee sustained a fracture to the right leg.

An employee was lifting a flat sub (sheet steel) in the flats robot cell (weld area). He was operating a hoist when his left little fingertip got caught between the lifting device hook and the flat sub. The employee sustained a partial transphalangeal amputation.

An employee was underneath a 35-foot boom truck and adjusting the transmission linkage when the truck jumped over the wheel chocks and rolled over the employee's right leg, resulting in a fracture.

A crane was being used to lift a debris tank from a rack. The tank crushed the employee's right hand, causing amputations to the employee's right ring finger and little fingertip.

An employee was removing a small sheet metal part out of the die of the brake press. The foot pedal was pressed, causing the part to lift and crush their left thumb against the die. The employee suffered an amputation to the thumb tip including the loss of flesh and the fingernail.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.