Gloucester Terminals LLC

An employee was working to unload cargo from a ship. A steel coil contacted the employee's left leg. The lower leg was fractured.

An employee was walking on a dock between racks when a jockey truck backed into her, pinning her against the racks. She suffered a fractured right femur.

An employee was trying to steady a load when his hand was caught between the load and the base, amputating two fingers above the second knuckle.

An employee began to experience arm and leg cramps while slinging slabs in the hold of a ship, requiring hospitalization for possible heat exhaustion.

An employee was helping to place chocks under a rail loaded on a truck. The rail fell off the truck and fractured his left leg.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

While preparing to install a new spool piece for a vapor and spent sulfuric acid line, an employee was working to ensure there was no residual product or pressure in the line before removing the 6-inch hose. The valve was cracked, and some spent acid still in the line sprayed out. The employee was standing off to the side and at a distance, but was still contacted by the hot acid, resulting in corrosive and thermal burns to their upper torso and mid-thighs of both legs.

An employee was driving a utility tractor rig when it struck the rear trailer of another utility tractor rig, which was traveling in the opposite direction. The glancing impact caused damage to the cab, and he sustained a laceration on right side of his face, a cervical fracture, two fractured left ribs, and a pelvic fracture. The employee was hospitalized.

The injured employee was standing by the controls for the electric spud system on the barge, preparing to raise the spuds. Meanwhile, an excavator was moving a mat on the deck. As the excavator swung from port to starboard, it's counterweight struck the injured employee s shoulder, causing them to lose balance and fall against the spud controls. The employee sustained bruises and contusions to their right shoulder and chest.

An employee was standing on the outside edge of a hopper barge while watching a skid steer push ore for an excavator (with a clamshell bucket) to unload. The excavator was on a work barge. The bucket of the excavator struck the employee and caused a near-amputation of their right arm and fractures of the ulna and radius of the left arm. The right arm required surgery.

An employee was inspecting a conveyor to see why it was not running. The employee entered the the conveyor motor area, tripped on a piece of angle iron welded to the floor, and fell. The employee sustained a fractured orbital bone.

An employee tripped over a stool and fell on the floor, resulting in a left displaced mid-cervical femoral neck fracture.

An employee was installing fence posts when they stepped into a recently dug hole that was not visible due to rainfall. The employee's leg was fractured.

An employee assisted in cleaning material from a conveyor pit. After the pit was cleaned, the employee proceeded to replace metal safety plates to ensure other employees did not fall into the pit. While replacing one of the last plates, the employee mis-stepped and fell approximately 5 feet into the pit. The employee was hospitalized with back/side bruising, elbow bruising, bone bruises, and/or fractured ribs.

An employee was inspecting a breaker box and turning on/off a circuit breaker when he was electrocuted.

An employee was walking on the sidewalk. When they stepped off the curb, they fell to the ground, resulting in fractures to their tibia, fibula, and a metatarsal.