Caught in running equipment or machinery during maintenance, cleaning · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Darby Equipment Company, LLC, 2940 N. Toledo Ave., TULSA, OKLAHOMA 74115
on — Amputations, affecting the finger(s), fingernail(s), unspecified.
Final narrative
An employee was cleaning and lubricating the drive chain on a pipe coating machine. The rag he was using to remove excess oil was caught in the machine, which resulted in his hand being pulled in. He suffered a partial amputation of the left index finger.
AmputationFinger(s), fingernail(s), unspecifiedMetal, woodworking, and special material machinery, n.e.c.
More severe injuries at Darby Equipment Company, LLC
An employee was removing a winch-line hook from a mandrel after they had completed bending a 24-inch diameter pipe. As he was unhooking the hook, the pipe moved and pinched his left index finger against the mandrel. The employee's finger sustained an partial amputation.
Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.
An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.
An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.
More severe injuries in this industry (NAICS 532490)
An employee was pulling a data cable through a ceiling. He fell through the ceiling, landing at ground level. He suffered a laceration to the forehead, a dislocated left little finger, a broken left ring finger, and a laceration to the liver.
On September 16, 2025, an employee was installing and adjusting spotlights on a performance stage that was under construction. While crossing the stage to speak with other contractors, the employee encountered a section of the stage where the elevation changed to a lower level. As the employee stepped down 14 inches to the lower level, his knee locked up and he fell to the stage. He subsequently rolled off the stage and fell approximately 2 to 3 feet to the floor, resulting in a fractured tibial plateau in his right leg.
An employee was delivering a 65-foot boom lift to a rental customer's construction site. The employee set up the ramp truck in the parking lot adjacent to the construction site. He elevated the boom 4-5 feet to clear a temporary fence. While driving the boom lift off the ramp, the wheels slid to the driver's side of the ramp truck, ultimately sliding off the ramp. The boom lift fell off the side of the truck and rolled onto its side. The employee sustained a fractured clavicle, a dislocated shoulder, separated/fractured ribs, a punctured lung, and a fractured left femur. The employee required surgery.
An employee was performing maintenance on a telehandler and installing a carriage lift cylinder. The employee was checking the alignment when the cylinder slipped and partially amputated his left middle finger.
An employee had just serviced a battery and was reinstalling it in a forklift using a battery extractor. The employee was trying to pull the battery out of the battery compartment when the extractor moved, causing the battery to shift on the rollers. The employee's right hand was crushed between the top of the battery and the battery compartment.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.