Part of occupant s body caught between vehicle and other object in nonroadway transport incident · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at OZARK MOUNTAIN POULTRY, 1420 Saint Louis, BATESVILLE, ARKANSAS 72501
on — Fractures, affecting the lower leg(s).
Final narrative
An employee was operating a powered pallet jack and heading to the north cooler door. When the employee made it to the north cooler, another pallet jack operator was leaving the cooler. The employee backed out to allow the other pallet jack operator to exit the cooler. After the other pallet operator exited, the employee turned the handle on his pallet jack and the machine went backwards. The pallet jack then hit the cooler guard and the employee's lower left leg was caught between the jack and guard, resulting in a broken lower left leg.
An employee was walking across an aisleway when he was struck by a forklift that ran over his leg. He sustained severe injuries requiring a possible leg amputation.
An employee was putting trays of chicks into the tray washer. The employee reached into the tray washer machine to remove a chick when his glove got caught on the chain and sprocket. He suffered lacerations to his right hand between the index and middle finger.
An employee was training on an rolling container carrier on the dry, non-frozen storage side of the distribution center. She made a turn around the end cap and her right foot struck the rail protecting the endcap racking. The employee's foot was fractured.
An employee was a passenger in a utility vehicle that was driving up a hill on a wooded trail. As the vehicle made a right turn, three fingers on the employee's right hand were caught against a tree and fractured.
An employee was scraping dried glue from the top lid of a hot glue pot. His left hand slipped and came into contact with the hot glue. He then suffered burns to his hands and fingers as he tried to remove the glue. He was hospitalized.
An employee was in a scissor lift approximately 20 feet above the ground to place a plastic tarp on a catwalk in order to catch condensation. They positioned the lift opposite the work area and stepped out of the scissor lift onto an I-beam. The employee fell from the I-beam to the ground. The employee was hospitalized with a skull fracture on the right side of their head and injuries to the chest and both eyes.
A maintenance employee was called to look at a pallet conveyor machine where a chain had fallen off a sprocket wheel. When the employee grabbed the loose chain, a light sensor caused the machine to restart. This created a pinch point between the chain and sprocket that caught the employee's left little finger. The finger was surgically amputated at the second knuckle.
The injured employee was standing by one of the stationary computers along the wall. There was a half-pallet located approximately 3 feet behind the employee that consisted of 12-pound boxes stacked six boxes high. A forklift was transporting a pallet that came in contact with the stationary pallet behind the injured employee, causing four boxes to fall and contact their legs. The injured employee was hospitalized with leg injuries.
An employee was using a box strapping machine to place straps on boxes when his right middle finger was caught in the machine, resulting in an open fracture to the distal phalanx.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.