Gabriel Steel Erectors Inc.

An employee was shooting studs with a 30-pound deck gun. As he twisted to reach an area of decking, he suffered a back injury. Later in the afternoon, he was hospitalized.

An employee had finished unloading materials from a truck onto a five-foot-high loading dock. The truck started to pull away. The employee stepped backward and fell off the loading dock onto the floor. He landed on his left side and was hospitalized with six fractured ribs.

An ironworker was using a magnetic drill to drill a steel beam. The drill bit caught his left glove and amputated his left thumb.

A propane heater burned the back of an employee's legs.

An employee was pushing carts into the chute area for customers to retrieve. The first of six carts struck the wall and caused the other carts to bounce back and strike the employee. The carts knocked the employee to the ground and she sustained a back injury.

An employee was loading a portable storage container onto a dovetail trailer. This requires hooking up a bridle to the container and lifting the container enough for the dovetail to begin to slide under it. The employee reached and held the bridle lock to allow the trailer to move under it when the trailer moved backward instead of forward and caught his finger. The employee's right middle finger was amputated between the fingernail and the first knuckle.

An employee was reaching over a small stack of steel billets on the ground to cut a strap. When the strap was cut, one of the billets (weighing 5,182 pounds) rolled down onto his right leg. He was pinned and suffered a broken tibia. The incident occurred while the employee was training.

On June 7, 2023, employees were unloading a box truck and rolling a reel of 2-inch plastic pipe to the back of the truck. As the employees were rolling the reel, the edge of the steel frame of the reel contacted the side of the truck. The injured employee s right little finger was caught between the reel and the truck, resulting in a laceration and fracture as well as a little finger amputation.

Employees were using a dolly to remove a trash compactor unit from a residential home. As they began to transport it out of the room and to the outside, the dolly encountered uneven ground. This caused the dolly and the unit to move quicker than expected. The injured employee's left hand was then caught between a nearby concrete column and the compactor unit, resulting in fractures of the left ring and middle fingers that required amputation.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was cleaning leaves with a backpack blower when he fell from a ladder, resulting in injuries to his head, neck, and back.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee slipped while descending in a stairwell, fell, and suffered multiple contusions/bruises to the head, neck, shoulders, knees, and back. She was hospitalized.

An employee's right middle finger was caught in a nip point. The employee suffered an amputation to the middle finger at the first knuckle.

An employee was directing trucks as they entered and left a highway work zone. A vehicle struck them, resulting in multiple fractures and other injuries. The employee was hospitalized.