Gabriel Steel Erectors, Inc.

An employee was shooting studs with a 30-pound deck gun. As he twisted to reach an area of decking, he suffered a back injury. Later in the afternoon, he was hospitalized.

An ironworker was using a magnetic drill to drill a steel beam. The drill bit caught his left glove and amputated his left thumb.

Two employees were rolling a piece of tube steel over when one of the employee's fingers was caught between the steel and the floor, resulting in a right middle fingertip amputation.

A propane heater burned the back of an employee's legs.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was cleaning leaves with a backpack blower when he fell from a ladder, resulting in injuries to his head, neck, and back.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee slipped while descending in a stairwell, fell, and suffered multiple contusions/bruises to the head, neck, shoulders, knees, and back. She was hospitalized.

An employee's right middle finger was caught in a nip point. The employee suffered an amputation to the middle finger at the first knuckle.

An employee was directing trucks as they entered and left a highway work zone. A vehicle struck them, resulting in multiple fractures and other injuries. The employee was hospitalized.