ND Paper, Inc.

An employee was adjusting a slitter blade on the winder and sustained a partial amputation of their right thumb tip.

An employee was changing a cleaner cone cap. The cone became pressurized with water, and the water stream pushed the employee into nearby equipment. The employee sustained a concussion; fractures to their skull and ribs; lacerations on their scalp, eyelid, and left thigh; and injuries to their pelvis and internal organs.

An employee connected a steam line to a hose to clean equipment when the fitting broke loose. They were struck by steam in the left inner thigh, resulting in burns that required hospitalization.

An employee was straining hot water from a pot of rice when the water splashed onto them, resulting in burns to their chest, arms, shoulder, and back.

An employee was making tea when she noticed tea grinds were collecting on the side and water was no longer dripping through the funnel. The employee was checking the funnel when boiling water and tea grinds spilled onto the left side of her body. The employee sustained burns to her neck, back, and arm.

An employee had turned off the ball valve on a waterpipe system and was removing the plug when the coupling system attached to the strainer came apart. Hot water sprayed on his arm and back, resulting in first- and second-degree burns that required surgery.

An employee was using a shovel to remove waste vermiculite from molten zinc. The metal had been placed in a bin and partially hardened. The employee broke through the partially hardened metal; still-molten metal flowed to the employee's steel-toed right boot and entered through the cloth boot tongue. The employee suffered a third-degree burn to the right foot and was hospitalized.

Tools and parts were being lowered to the ground from an elevated platform in a 5-gallon bucket. The rope being used to lower the bucket failed; the tools and parts fell and lacerated the left forearm and upper left leg of an employee on the ground.

An employee was tracking an infeed belt on a scrap hogger when their right arm was caught between the belt and a roller. The arm was broken and the employee's shoulder was dislocated. The employee was hospitalized.

An employee was working to clear a jam from a paper napkin folder. The ram that advanced the napkins pushed the employee's right arm into the side of the machine, causing several lacerations and a hairline fracture.

An employee was troubleshooting overflowing ink on a printer-slotter machine when their right ring fingertip was caught in a guarded roller, resulting in a partial amputation.

An employee was disconnecting wires in preparation to swap out a refiner motor when they contacted energized equipment and sustained an electrical shock. The employee was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.