Best Steel LLC

An employee was installing horizontal bracing. They were approximately 32 feet high in an extended scissor lift when one of the wheels broke off. The scissor lift tipped over and the employee struck the ground, sustaining a concussion and two broken ribs.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.