The Toro Company

An employee was moving materials in an area behind the building using a stand-up loader. While backing up, his ankle was pinned between a metal rack and the loader resulting in a broken ankle.

An employee was taking inventory while on an order picker elevated at approximately 16 feet when they fell to the warehouse floor. The employee sustained a head laceration, liver laceration, and fractures to the pelvis, wrist, and femur.

An employee was using a stock chaser ladder to retrieve a part from stock. The employee fell to the ground, and the part struck her in the face, resulting in a laceration and fractures to her face and teeth.

An employee climbed onto a mower that was raised 18 inches on a final assembly platform to install a steering wheel. As the employee was climbing down from the mower, her foot missed the 18-inch platform and she fell to the concrete plant floor, fracturing her L4 vertebra.

An employee was using a manipulator/hoist to lift a mower deck off an assembly table when the mower blade became caught on an attachment on the table. The table then lifted with the blade as the deck was rising. The employee went to push the table back down and release it from the blade. At the same time, the controls were activated to lower the manipulator/hoist. The employee's left thumb was then pinched between the table and the manipulator/hoist, amputating the distal portion of the thumb just below the nail.

An employee was drying and finishing vehicles when a vehicle door closed on their left middle fingertip and amputated it.

An employee was climbing down from a tractor trailer bed when they lost their footing and grabbed onto the roll-up door to stop the fall. The roll-up door then fell onto the employee's hand, resulting in a hand fracture that required surgery.

An employee was attempting to remove a tarp from a flatbed trailer when the trailer handle struck the employee in the chest, resulting in two broken ribs and a punctured lung.

An employee was near a backhoe while the operator was getting a broom. The broom handle struck the lever that actuates the swing of the backhoe bucket. The bucket then struck the injured employee, pinning him to the outrigger. The employee suffered crush injuries to the chest.

The injured employee was being trained on loading trucks in the load out bay. The injured employee and his supervisor climbed the stairs that run parallel to the truck and trailer, walked to the upper platform used for observation and sample taking, and saw that the lid of the grain trailer was closed. The employees began working to open the lid which appeared to be stuck due to cold weather. The injured employee pulled on one of the pivot arms that connect the lid to the main body of the trailer. As the lid began to open, the employee s right hand slipped down on the pivot arm and his index finger was caught between the pivot arm and the base of the pivot arm. The employee s right index finger was fractured and three nerves were severed. The employee was hospitalized.

At 12:55 p.m. on October 8, 2025, a pneumatic cylinder press was activated while an employee's hand was resting on it. The moving shaft and top portion of the machine descended, catching the employee's right middle finger and amputating the fingertip (without bone loss).

An employee had been providing lawncare service and was driving back to the main facility when he experienced severe cramping due to heat stress. The employee was hospitalized for dehydration.

At about 5:15 p.m. on June 14, 2025, an employee was using a walk-behind mower to mow middle islands along a road. A support truck with an arrow board sign was following behind to control traffic. The truck lurched forward and struck the employee from behind, pinning the employee against the mower. The employee suffered a fractured hip, a right iliac wing fracture, right femoral nerve damage, and puncture wounds to the right leg. The employee was hospitalized.

A welder in the fabrication shop was straightening a wheel tab with a hammer and struck his left hand. The employee was hospitalized with a fractured hand.

A sprayer boom assembly fell off a sawhorse when the C-clamp was removed and it struck an employee. The employee suffered a separated collarbone and three broken ribs.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.