Performance Pallet Corp.

An employee was performing quality control on an 8-foot stack of pallets while standing on a 4-foot ladder. The employee was using an air hose to blow dust off of the pallets. The air hose was wrapped around the ladder. When the employee tugged on the air hose, they fell off the ladder onto the ground and fractured their forearm.

An employee was building pallets using a nail gun. He tripped on a board on the floor, and the gun shot a nail through his hand.

An employee was unjamming boards from a rip saw and contacted the spinning blades. He sustained three lacerations to the left hand and forearm, broken fourth and fifth metacarpal bones in the left hand, and a broken ulna in the left forearm. The machine was unguarded at the time.

An employee was performing maintenance work on a wood packaging line to fix a portion of plastic that was stuck when his left middle finger was pinched between the machine basket and a metal bar frame, amputating it above the first knuckle.

On a three head saw machine, an employee was using a hand tool/bar to lift a chain that had a jammed buckle. The employee pressed the foot pedal to move the chain and free the buckle. When the pedal was pressed, the chain moved and caused the hand tool/bar to jerk, which pinched and amputated the employee's right-hand index finger between the chain guard and tool.

An employee was installing wood trim surrounding a skylight inside a home. While holding a piece of trim in it's desired location, his pneumatic nail gun discharged, sending a 3/4-inch pin nail into his left forearm.

An employee removed a safety valve on a trailer that unknowingly contained nitrogen gas. The gas released from the trailer and pushed the employee backward off a scaffold approximately 10 feet before they struck a garage door, resulting in a pelvic injury.

An employee was sitting at her workstation when a nail gun malfunctioned and shot a nail into her left leg. She suffered a puncture and blood vessel injury and was hospitalized.

On November 25, 2023, an employee was using a high-pressured water hose to perform sewer line cleaning operations. The employee's right little finger and palm were lacerated by pressurized water from the hose.

An employee was hydroblasting when they slipped and the pressurized water stream lacerated their left ankle.

An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.

An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.

An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.