JEFFERSON INDUSTRIES CORPORATION

An employee was making an adjustment to the welding arm of a stationary spot welding machine when her right index finger was smashed on the up-stroke, causing a partial amputation of the fingertip.

An employee was changing over a jig cart. The lock pin to hold the jig in place would not advance through the plate on the jig. When the lock pin became unstuck it crushed the employee's right middle fingertip resulting in an amputation.

On March 4, 2019, an employee was working on a drill press when his shirt sleeve was caught in the chuck on the press and wrapped around his left thumb. His thumb was amputated.

On August 16, 2016, at approximately 10:59 p.m., an employee was attempting to fix a sensor inside the enclosure of a laser weld cell. While the employee was inside the enclosure, a carrier that moved parts into the welding machine moved and struck the employee in the left leg, puncturing the left thigh.

An employee passed out and was found unconscious. The employee regained consciousness and was found to have a gash near the right temple. Blood was observed on a parts cart and the floor where the employee was first found. EMS responded and took the employee to Doctor's West Hospital. A cat scan was performed and the employee was found to have minor internal brain bleeding. The employee was taken to Grant Hospital for further tests.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee was making repairs to a milling machine located in the mold shop. While using a screwdriver to make adjustments, the machine energized and struck the employee. The employee's right arm was fractured.

An employee was breaking down dunnage to prepare totes and trays to go through a tote washer. A tow motor driver asked the employee to move a cart that was in the way so the tow motor could remove a gaylord. The employee moved the cart and then stepped away from the tow motor. As the employee moved to an area between carts, his right foot got caught by a cart, causing him to twist and fall on top of a cart, landing on the left flank of his torso. The employee suffered a hemorrhage on his left flank.

An employee tripped over a computer cord and fell fracturing their femur.

Three employees were installing a transfer rail in a press. There were two employees holding the rail and the injured employee was at the end of the rail guiding the rail into the bracket. The task was done manually with no mechanical equipment. The employee had their finger at the end of the rail and went to make sure the rail was lined up while the other two employees pushed it into the bracket, causing their finger to become pinched between the rail and bracket. The employee's middle fingertip was amputated. Protective gloves were worn at the time of the incident.

An employee was walking across the dock, interacting with forklift drivers on what was being loaded. A forklift drove forward with a tall load on the forks. The employee was struck by the load (running board/rocker panel rack) on the forklift. The employee sustained several contusions and an injury to their right Achilles tendon that required surgery.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.