Caught in or compressed by equipment or objects, unspecified · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Twin Rivers Paper Company, 1701 Jefferson Parkway, PINE BLUFF, ARKANSAS 71601
on — Amputations, affecting the fingertip(s).
Final narrative
An employee was changing out a paper roll set on a winder. The core chucks were being retracted, and he was clearing a piece of paper from them when the tip of his left index finger was caught in the wedge hole. As the chuck retracted into the outer cylinder, about a centimeter of the fingertip was sheared off.
HospitalizedAmputationFingertip(s)Slitters, winders-paper production
An employee was clearing a shaft in a confined space when a microbiocide chemical landed in their eye. The employee was hospitalized for chemical burns to the eye and back.
An employee operating a 30-ton mobile crane was backing out down a hill when the brakes felt like they were not working, so the employee opened the door and exited the crane. He jumped approximately 6 feet and fell on his right leg at an odd angle, breaking it.
On or about 03/27/2015, an employee was hospitalized with injuries sustained from getting caught between a brake and reel while pushing an empty paper spool.
Employee was pulling shavings on a winder at the trim chute and contacted the trim slitter suffering an angled cut to the nail bed and tip of the right index finger.
An employee was changing mud cups in the hopper cylinders of a concrete pump truck. The cylinders moved and three of the employees fingers were amputated.
An employee was standing on the rig floor next to a polishing unit. His hand was placed on the polishing unit when the pump was lowered, resulting in amputation of their right thumb, ring, and middle fingertips.
An employee was using air to blow out the air wash to the blender and grinder station. As the employee reached to verify that the air wash was clean, the unit pinched and amputated their fingertip.
An employee was retrieving a lost drill pipe with a lifting bail when their left thumb got pinched between the table and handle of the lifting bail while trying to re-thread the pipe to lift it out. The employee suffered an amputation to the left thumb.
An employee was removing a core chuck from a stationary roll when their right ring finger was pinched between the chuck and the roll. The employee's fingertip was amputated.
More severe injuries in this industry (NAICS 322121)
Tools and parts were being lowered to the ground from an elevated platform in a 5-gallon bucket. The rope being used to lower the bucket failed; the tools and parts fell and lacerated the left forearm and upper left leg of an employee on the ground.
An employee was tracking an infeed belt on a scrap hogger when their right arm was caught between the belt and a roller. The arm was broken and the employee's shoulder was dislocated. The employee was hospitalized.
An employee was working to clear a jam from a paper napkin folder. The ram that advanced the napkins pushed the employee's right arm into the side of the machine, causing several lacerations and a hairline fracture.
An employee was troubleshooting overflowing ink on a printer-slotter machine when their right ring fingertip was caught in a guarded roller, resulting in a partial amputation.
An employee was disconnecting wires in preparation to swap out a refiner motor when they contacted energized equipment and sustained an electrical shock. The employee was hospitalized.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.