TDIndustries, Inc.

An employee was using an acetylene torch to cut piping. A flash fire occurred and burned the employee's left hand, chest, face, and left ear. The employee was hospitalized.

On July 9, 2024, an employee was troubleshooting a relay on the low voltage inside a water source heat pump when he contacted an electrical component and was shocked. The employee sustained a burn to his left index fingertip.

An employee was descending an 8-foot step ladder from the fifth rung when he missed a step and fell to the ground. The employee sustained a tibia fracture.

Two employees were installing a 6-inch test T in a vertical 6-inch cast iron storm riser. The T was to be placed approximately 2 feet above floor level and required cutting and removing a section of the 6-inch storm riser. The two employees placed a riser approximately 5 feet above the section they intended to remove and utilized a 5-foot piece of 2" cast iron to support the riser clamp and ultimately the 6-inch cast iron pipe above the section being removed. They then cut and removed the 12-inch section of pipe. Employee 1 began installing the rubber no hub gasket on the cast iron riser coming through the floor while Employee 2 was installing the rubber no hub gasket on the cast iron riser coming down from the floor above. As Employee 2 was installing the rubber no hub gasket on the upper section of pipe the riser clamp slid off the 2-inch cast iron. This resulted in the upper section of pipe falling when the no hub band holding it in place failed to support the weight of the section of pipe. The upper section of pipe fell on Employee 2's right thumb smashing it between the two sections of pipe. The employee's thumb was fractured and lacerated requiring surgery to repair.

Three employees were installing a no-hub band over a 12-inch cast iron 90-degree elbow and a stub that went to a roof drain. The no-hub band broke during installation, and they descended in a lift to get a new one. The elbow fell down on one of the employees from about 20 feet above. It struck his head, which caused him to fall and hit his head on the toe board of the scissor lift. The employee sustained injuries to the head, neck/spine, and shoulder.

An employee was operating a machine when a wire pulled his right glove resulting in amputation of the index and middle fingertips.

An employee was grinding chicken when their right index fingertip was caught in the grinder and amputated.

An employee was sharpening peeler blades when their shirt was caught in the grinding wheel. The employee sustained tendon damage and a crushed right hand.

An employee was passing through a large metal door when the door closed on the employee, resulting in a cracked rib.

An employee was preparing to cut lumber on a panel saw when the clamp engaged and caught the employee's left middle finger, resulting in a fingertip amputation.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.

An employee was closing the side cargo door to a company van. The tip of his finger got caught between the door and the door jamb, resulting in a partial amputation.

While working at a customer's residence, an employee was cutting tape with a box cutter to wrap insulation for a piece of pipe. The box cutter struck a hardened object within the wall causing it to bounce back and puncture the employee's right eye. The employee was hospitalized.

An employee was assembling a baker type scaffold. He was beginning to transverse down the scaffold, approximately six feet off the ground, when the scaffold tipped over and he fell. The employee was hospitalized with a fractured femur.

An employee was trimming out sprinklers on the exterior of a building when he fell off an extension ladder. He landed on the ground and sustained fractures to his nose and arm.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.