INTERCERAMIC INC.

An employee was operating a dryer kiln when an alarm went off indicating that one of the two limit switches of the centering device control was not functioning properly. In order to reach the centering device control limit switch, the employee used a rod and kneeled down stretching his body/hand forward between the dryer exit and a column of an unloader machine. The employee's body was caught between the exiting tile cart and the column of the unloader machine resulting in fractured ribs.

An employee was pushing a tile cart that was on an automated track into a dryer. The employee got caught between two carts and was struck by a cart. The employee sustained a broken pelvis.

On November 16, 2023, at around 3:30 p.m., a subcontracted employee was painting a door jam on a three-story house when he fell 20 feet through an opened elevator shaft to the floor below. The employee sustained fractured vertebrae that required hospitalization.

Employees were removing and replacing skylights on a metal roof. The injured employee's lanyard became tangled and they fell through the skylight to the ground 16-18 feet below. The employee suffered fractures to the wrist, ribs, and hip.

An employee was requested by a client to string wire on top of an auditorium. He used a boom lift to access a beam and then exited the boom lift to walk on the beam. He then stepped down on a drop ceiling, lost balance, and fell. The drop ceiling caved in and the employee fell 20 feet onto bleachers sustaining injury to his abdominal area and lower left leg. The employee was wearing a harness, but it was not connected to an anchoring point at the time of the fall.

An employee was installing decking (steel grates) in a new construction steel framed building. The employees were working approximately 22' above the next lower level, which was a concrete ground floor. The decking was pre-cut with the floor opening prior to installation. Shortly after installing the floor opening, the employee fell through the floor opening, approximately 18' onto a section of metal ductwork, resulting in fractures to the skull, ribs, thorax, and lumbar vertebra, as well as an ear laceration.

An employee was taking measurements of an area for drywall when they stepped backward into a partially covered hole in the floor. The employee fell approximately 17 feet to the level below, sustaining a forehead fracture and avulsion, a right shoulder dislocation, a left forearm fracture, left knee tendon and meniscus tears, as well as multiple contusions and abrasions.

An employee was operating a press when the timing belt came loose. The machine was turned off. As the employee began to adjust the belt, the pulley on the table moved and his right middle finger was caught between the belt and pulley and amputated.

An employee was operating a dryer kiln when an alarm went off indicating that one of the two limit switches of the centering device control was not functioning properly. In order to reach the centering device control limit switch, the employee used a rod and kneeled down stretching his body/hand forward between the dryer exit and a column of an unloader machine. The employee's body was caught between the exiting tile cart and the column of the unloader machine resulting in fractured ribs.

An employee fell to the floor while running through a building. The employee suffered a broken left femur.

An employee was adjusting a chain on a press dryer. The employee's right middle and ring fingers were caught in the chain and sprocket, and the fingertips were amputated.

An employee fell from an extension ladder while working to correct a leak from a hydraulic hose fitting. The employee was hospitalized.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.