FINFROCK DESIGN-MANUFACTURE-CONSTRUCT, LLC

An employee was helping prepare a concrete form bed in a manufacturing facility. The employee's right middle finger was pinched between a magnet and the metal form bed while he was cradling it to hold it in place.

While closing a gate, an employee's finger was pinched in the gate's roller resulting in amputation of the left pinky fingertip.

An employee was working with a hydraulic strand jack machine when a stream of hydraulic fluid entered their right middle finger. The employee was hospitalized with a possible infection.

An employee was setting up a precast concrete form when he began to feel dizzy and nauseous. The employee was hospitalized for dehydration.

An employee was setting up a precast concrete bed when his finger was crushed between the sled and end of the precast bed, resulting in a partial finger amputation.

An employee was performing finishing work on a residential driveway when they began to experience body cramps and were hospitalized for heat stress and dehydration.

An employee was staking tomato plants on a farm. The employee began to feel sick and collapsed, suffering from dehydration and heat shock.

An agent was participating in SWAT team selection and was performing various physical fitness skills including running and exercise intervals. The agent experienced dehydration and a muscular injury that required hospitalization.

An employee was traveling back from work when they became ill and experienced dizziness due to heat exhaustion.

On September 26, 2023, an employee was delivering packages when he began to feel ill with a pain in his side. He was hospitalized for heat exhaustion and dehydration.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.